HPC015S Infrared Beam Wifi People Counter Sensors

Please check below short video for our HPC015S infrared beam wifi people counter sensors.

HPC015S infrared beam wifi people counter sensors is small-sized and battery-powered. The data can be uploaded to the cloud through WIFI automatically. It integrates two operation modes for choice: standalone and network. Parameter settings and data browsing can be done through a smartphone.

Specification

1. Package Contents of  HPC015S Infrared Beam Wifi People Counter Sensors

Opening the packing box, there are a RX (receiver), a TX (transmitter), two rechargeable lithium batteries, a charger, double-sided tapes, two mounting brackets and a small wrench.

2. Installation of Cover Plate

There is a cambered notch at the top of receiver and transmitter. Use the thumbs of both hands to press the cover plate and the base, then open the cover plate carefully. After the installation and settings are finished, the cover plate can be buckled on.

Attention!

Be sure to install the cover plates in correct direction.

The black bar area of the cover plate is infrared light transmission area. The infrared light of transmitter emits infrared ray beams through the area. Receiver receives the infrared ray beams and shows the contents of OLED display screen through the area.

3. Introductions of Receiver Panel

After installing the battery, OLED display screen will show the booting information. By touching the touch sensor button, you can switch the contents on display screen: the current battery remaining capacity (BAT) and product serial number (SN), working parameters, open and close time, start AP menu and so on. If without touch operation for more than 10 seconds, the display screen will automatically turn off to reduce power consumption.

There are three indicator lights for receiver:

Red indicator light is used as the infrared focus indication. When receiver cannot receive the infrared signal from transmitter, the red indicator light will flash. Through this indicator light, you can easily find the suitable mounting position of transmitter.

Yellow indicator light is used for low-voltage battery alarm and charge indications. When the battery voltage is too low, the indicator light will flash to remind you to charge or replace the battery. When the battery is charged through the USB interface, the indicator light is on. If you do not want to use battery, turn the DIP switch of power supply mode to the "V" position, then you can use the USB interface to charge the receiver.

Blue indicator light is for WIFI network transmission or data saving indication.

4. Introductions of Transmitter Panel

There are two indicator lights for transmitter:

Red indicator light is used as low-voltage battery alarm indication. When the battery voltage is too low, the indicator light will flash to remind you to charge or replace the battery.

Blue indicator light is self-test indication. When the battery is installed, the blue light will go out after flashing 3 times, that means the device is normal.

If you do not want to use battery, turn the DIP switch of power supply mode to the "V" position, then you can use the USB interface to charge the transmitter.

There are two DIP switches on transmitter. Switch 1 is used to control the frequency of transmitter, which should be corresponding to the detection speed of receiver. If the receiver is set to high speed, you need to turn switch 1 of transmitter to upside position; on the contrary, turn switch 1 to downside position. Switch 2 is used to set high power (upside position) or low power (downside position). If switch 2 is set to upside position, the infrared signal can transmit longer distance. After changing the position of DIP switch, you need to re-install the battery to make it effective.

5. The Usage of Charger

When the battery remaining capacity is low, please use the matched charger to charge it. The maximum charging process takes about 6 hours. The green indicator light is on after the battery is fully charged. The charger can charge two lithium batteries at the same time. The “+” on battery should toward the direction of indicator light.

6. Preparations before Installing Receiver

First of all, you need to ensure that the receiver will work in standalone mode or network mode. If in network mode, it is necessary to ensure a good WIFI signal coverage in the installation location. You can use a smartphone to check the WIFI network signal strength in the installation location. If the WIFI signal strength is too weak, the battery power consumption of receiver will increase when connecting network or the receiver maybe not able to connect the network.

7. Data Browsing of HPC015S Infrared Beam Wifi People Counter Sensors

Click “DATA LIST” button in login page, then you can browse the total daily data in the last 30 days and the total monthly data in the last 12 months. You can clear today’s data by clicking “Clear” button.

The data on display screen will be cleared automatically before the open time every day. The total in and out data from open time to close time will be displayed, and the data will not be affected by battery replacement.

8. The data can be displayed on TV screen for better controlling the people flow. The system will have Flash/ Alarm when the stay number exceed the maximum number you set. There are 3 solutions for your choice, as below:

(1) Solution for smart TV (Can install APP and have LAN port)

(2) Solution for any TV (with HDMI or VGA port)

(3) Solution for smart TV (Can install APP and have LAN port): Check the data on a Smart TV screen through our cloud platform in China.

Please click the below picture for our people counting camera systems: